工業超聲波清洗機憑借高效清潔能力，在制造業等領域廣泛應用。想要充分發揮其效能，規范且正確的操作必不可少。從清洗前的準備、設備啟動運行到清洗后的收尾工作，每個環節都有特定的操作流程和注意要點。

　　Industrial ultrasonic cleaning machines are widely used in manufacturing and other fields due to their efficient cleaning capabilities. To fully utilize its effectiveness, standardized and correct operation is essential. From preparation before cleaning, equipment start-up and operation to final work after cleaning, each link has specific operating procedures and key points to note.

　　清洗前的細致準備

　　Careful preparation before cleaning

　　在使用工業超聲波清洗機前，首先要明確清洗對象和污垢類型。不同的工件材質、形狀，以及附著的油污、銹跡、碎屑等污垢，對清洗方式和清洗液有不同要求。比如金屬工件表面的頑固油污，與塑料工件表面的灰塵雜質，所適用的清洗液和清洗參數就存在差異。確定清洗對象后，選擇合適的清洗液至關重要。清洗液分為水基、溶劑基等多種類型，水基清洗液環保且對水溶性污垢去除效果好；溶劑基清洗液則擅長溶解油脂等有機污垢。按照說明書要求，將適量清洗液倒入清洗槽內，同時加入一定比例的清水稀釋，確保清洗液濃度符合標準。

　　Before using an industrial ultrasonic cleaning machine, it is necessary to first clarify the cleaning object and the type of dirt. Different workpiece materials, shapes, and attached dirt such as oil stains, rust, and debris have different requirements for cleaning methods and cleaning solutions. For example, the stubborn oil stains on the surface of metal workpieces and the dust impurities on the surface of plastic workpieces require different cleaning solutions and cleaning parameters. After determining the cleaning object, it is crucial to choose the appropriate cleaning solution. Cleaning solutions are divided into various types such as water-based and solvent based. Water based cleaning solutions are environmentally friendly and have good removal effects on water-soluble dirt; Solvent based cleaning solutions are good at dissolving organic dirt such as grease. According to the instructions, pour an appropriate amount of cleaning solution into the cleaning tank and dilute it with a certain proportion of water to ensure that the concentration of the cleaning solution meets the standard.

　　接著，檢查清洗機的運行狀態。查看設備外觀有無損壞，確保電源線、控制面板等部件無破損、無漏電隱患。檢查清洗槽內是否潔凈，如有殘留雜質需及時清理，避免影響清洗效果。同時，確認超聲波發生器、加熱裝置（若有）等核心部件正常，各連接部位牢固。對于循環過濾系統，要檢查濾芯是否堵塞，若發現濾芯積聚較多雜質，應及時更換，保證清洗過程中液體的循環暢通。

　　Next, check the operating status of the cleaning machine. Check the appearance of the device for any damage, ensuring that the power cord, control panel, and other components are not damaged or have any potential leakage hazards. Check if the cleaning tank is clean, and promptly clean any residual impurities to avoid affecting the cleaning effect. At the same time, confirm that the core components such as the ultrasonic generator and heating device (if any) are functioning properly, and that all connecting parts are securely fastened. For the circulating filtration system, it is necessary to check whether the filter element is clogged. If a large amount of impurities are found in the filter element, it should be replaced in a timely manner to ensure smooth circulation of liquid during the cleaning process.

　　此外，對待清洗工件進行預處理也很關鍵。去除工件表面較大的塊狀雜質、多余的包裝物，對于容易松動的零部件，進行加固或拆卸處理，防止在清洗過程中脫落損壞。同時，將工件合理擺放于清洗籃或清洗架上，避免相互堆疊、擠壓，確保每個工件都能充分接觸清洗液，保證清洗的均勻性和全面性。

　　In addition, pre-treatment of the cleaned workpiece is also crucial. Remove large block like impurities and excess packaging on the surface of the workpiece. For parts that are prone to loosening, reinforce or disassemble them to prevent them from falling off and being damaged during the cleaning process. At the same time, place the workpieces reasonably on the cleaning basket or rack, avoid stacking and squeezing each other, ensure that each workpiece can fully contact the cleaning solution, and ensure the uniformity and comprehensiveness of cleaning.

　　規范啟動與運行操作

　　Standardize startup and operation operations

　　準備工作完成后，接通工業超聲波清洗機電源，打開設備總開關。此時，設備控制面板亮起，顯示相關參數。根據清洗對象和清洗液特性，在控制面板上設置清洗時間、超聲波頻率、溫度（若有加熱功能）等參數。一般來說，清洗時間根據污垢程度設定，從幾分鐘到幾十分鐘不等；超聲波頻率常見有低頻、高頻等，低頻適合去除大顆粒污垢，高頻對精細工件的深層清潔效果更佳；溫度方面，適當提高溫度能增強清洗液的活性，但要注意不能超過工件和清洗液的耐受范圍。

　　After the preparation work is completed, turn on the power of the industrial ultrasonic cleaning machine and turn on the main switch of the equipment. At this point, the device control panel lights up and displays relevant parameters. According to the characteristics of the cleaning object and cleaning solution, set parameters such as cleaning time, ultrasonic frequency, temperature (if there is heating function) on the control panel. Generally speaking, the cleaning time is set according to the degree of dirt, ranging from a few minutes to several tens of minutes; Ultrasonic frequencies commonly include low frequency, high frequency, etc. Low frequency is suitable for removing large particle dirt, while high frequency has a better deep cleaning effect on fine workpieces; In terms of temperature, increasing the temperature appropriately can enhance the activity of the cleaning solution, but it should be noted not to exceed the tolerance range of the workpiece and the cleaning solution.

　　設置好參數后，按下啟動按鈕，設備開始運行。此時，觀察清洗槽內液體的變化，正常情況下，會看到液體中產生大量細密的氣泡，這是超聲波空化作用的表現。同時，注意傾聽設備運行聲音，若出現異常噪音或振動，應立即按下停止按鈕，檢查設備是否存在部件松動、異常磨損等問題，排除故障后再重新啟動。

　　After setting the parameters, press the start button and the device will start running. At this point, observing the changes in the liquid inside the cleaning tank, under normal circumstances, a large number of fine bubbles will be observed in the liquid, which is a manifestation of ultrasonic cavitation. At the same time, pay attention to the sound of the equipment running. If there is any abnormal noise or vibration, immediately press the stop button to check for loose components, abnormal wear, and other issues. After troubleshooting, restart the equipment.

　　在清洗過程中，還需定期觀察清洗效果?？梢匀〕鰝€別工件查看表面污垢去除情況，若發現清洗效果不理想，可適當延長清洗時間、調整超聲波頻率或更換清洗液濃度。對于一些復雜結構或污垢嚴重的工件，必要時可中途暫停設備，將工件翻面或調整位置，確保各個部位都能得到充分清洗。

　　During the cleaning process, it is also necessary to regularly observe the cleaning effect. Individual workpieces can be taken out to check the removal of surface dirt. If the cleaning effect is not ideal, the cleaning time can be extended appropriately, the ultrasonic frequency can be adjusted, or the concentration of the cleaning solution can be changed. For some complex structures or heavily soiled workpieces, it is necessary to pause the equipment midway, flip or adjust the position of the workpiece to ensure that all parts can be thoroughly cleaned.

　　清洗后的妥善處理與設備維護

　　Proper handling and equipment maintenance after cleaning

　　清洗完成后，設備自動停止運行或按下停止按鈕結束清洗。使用專用工具，如夾子、手套等，小心取出清洗籃或工件，避免燙傷（若清洗液溫度較高）和劃傷。將清洗后的工件放置在干凈的區域，進行后續處理，如用清水沖洗去除殘留清洗液，再進行干燥、防銹等操作。對于清洗液，若還能繼續使用，可通過過濾裝置去除其中的雜質后，儲存于專用容器中；若清洗液已失效，則按照相關規定進行妥善處理，防止污染環境。

　　After the cleaning is completed, the equipment will automatically stop running or press the stop button to end the cleaning. Use specialized tools such as clips, gloves, etc., carefully remove the cleaning basket or workpiece to avoid burns (if the cleaning solution temperature is high) and scratches. Place the cleaned workpiece in a clean area for subsequent processing, such as rinsing with clean water to remove residual cleaning solution, and then performing drying, rust prevention, and other operations. For cleaning solution, if it can still be used, impurities can be removed through a filtering device and stored in a dedicated container; If the cleaning solution has failed, it should be handled properly according to relevant regulations to prevent environmental pollution.

　　設備使用完畢后，要進行全面清潔和維護。排空清洗槽內的剩余清洗液，用清水沖洗槽體，去除殘留污垢和清洗液。對于設備表面，使用干凈的濕布擦拭，保持外觀整潔。檢查設備各部件，如超聲波換能器、加熱管等，查看是否有結垢、腐蝕等情況，如有需要，按照說明書要求進行清理或維護。定期對設備的電氣系統進行檢查，確保線路連接牢固，無老化、破損現象。同時，做好設備運行記錄，包括使用時間、清洗對象、清洗效果等信息，以便后續分析設備性能和優化清洗工藝。

　　After use, the equipment should be thoroughly cleaned and maintained. Drain the remaining cleaning solution from the cleaning tank, rinse the tank with clean water to remove residual dirt and cleaning solution. For the surface of the equipment, wipe it with a clean damp cloth to maintain a neat appearance. Check all components of the equipment, such as ultrasonic transducers, heating tubes, etc., for scaling, corrosion, etc. If necessary, clean or maintain according to the instructions. Regularly inspect the electrical system of the equipment to ensure that the wiring connections are secure and free from aging or damage. At the same time, keep good records of equipment operation, including usage time, cleaning objects, cleaning effects, and other information, in order to analyze equipment performance and optimize cleaning processes in the future.

　　掌握工業超聲波清洗機的正確操作方法，從清洗前的準備、運行中的規范操作到清洗后的維護，每個步驟都做到嚴謹細致，不僅能確保清洗效果，提高工作效率，還能延長設備使用壽命，為工業生產中的清潔工作提供可靠保障。

　　Mastering the correct operation method of industrial ultrasonic cleaning machine, from preparation before cleaning, standardized operation during operation to maintenance after cleaning, every step is rigorous and meticulous, which not only ensures the cleaning effect and improves work efficiency, but also extends the service life of equipment, providing reliable guarantee for cleaning work in industrial production.

　　本文由超聲波清洗機友情奉獻.更多有關的知識請點擊:http://www.98146.com.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from a high-pressure deburring cleaning machine For more information, please click: http://www.98146.com.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message